Epson TM-T88II Series Manual de Instruções Página 130
- Página / 154
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Appendix A-4 Rev. A
❏ Data transmission should not ignore the signal nAck or Busy. An attempt to transmit data with
either signal, nAck or Busy, ignored can cause lost data. (Data transmission to the printer
should be made after verifying the nAck signal or while the Busy signal is low.)
❏ Interface cables should be as short as possible.
Precautions on receiving status from the printer
The printer status transmission is available by using the both-way communication facility in the
Nibble/Byte mode in accordance with the IEEE 1284 mode.
The following precautions must be taken for receiving the status from the printer.
❏ The allowable capacity of the printer’s internal buffer is 100 bytes. Status signals exceeding
this capacity will be discarded. To prevent possible loss of status data, the host should
always be ready for data reception (reverse mode).
❏ When ASB is used, the host should be in the wait state for data reception (reverse idle
mode). When this state is not available, the host should enter the reverse mode to always
monitor the presence of data.
❏ When ASB is used, preference should be given to the ASB status for transmission over the
other status signals. Any accumulated ASB status signals left for transmission from the last
to the newest ASB status transmission should be transmitted together at one time as one
ASB status showing the change has been made, followed by the latest ASB status.
Example: In the normal (wait) state, the ASB status is configured as follows:
1st status 2nd status 3rd status 4th status
0000 1000 0000 0000 0000 0000 0000 0000
When the following sequence of operations is performed, near end detection, cover open, cover closed, the
following pieces of data are accumulated.
1st status 2nd status 3rd status 4th status
1 0000 1000 0000 0000 0000 0011 0000 0000 Near end detection
2 0010 1000 0000 0000 0000 0011 0000 0000 Cover open
3 0000 1000 0000 0000 0000 0011 0000 0000 Cover closed
When the ASB status is received following this, a total of 8 bytes of ASB will be transmitted as follows.
Accumulated ASB (1+2+3)
1st status 2nd status 3rd status 4th status
Accumulated ASB (1+2+3) 0010 1000 0000 0000 0000 0011 0000 0000
+ 1st status 2nd status 3rd status 4th status
The latest ASB (3) 0000 1000 0000 0000 0000 0011 0000 0000
- TM-T88 Series 1
- SEIKO EPSON CORPORATION 4
- Modular type connectors 5
- FCC CLASS A 5
- Introduction 6
- WARNING: 7
- Revision Sheet 8
- Contents 9
- Rev. A vii 11
- Chapter 1 13
- Printing Specifications 14
- Character Specifications 15
- Auto Cutter 15
- Paper Roll Supply Device 16
- Paper Specification 16
- Printable Area 17
- Internal Buffer 18
- Electrical Specifications 18
- Reliability 19
- Environmental Conditions 20
- Connectors 21
- Power Supply Connector 22
- CAUTIONS: 24
- RS-232 serial interface 25
- (continued) 27
- Reset switching 29
- Reset DC characteristics 29
- Buttons and Switches 30
- Panel Button 31
- DIP Switches 31
- Transmission speed 32
- DIP switch 2 32
- Print density selection 32
- For parallel interface model 33
- DIP switch 1 33
- DIP switch 2 33
- Panel LED 34
- Self-test 35
- Hexadecimal Dump 35
- Paper Sensors 36
- Standard Accessories 37
- Consumables 38
- Input specifications 39
- Output specifications 39
- Chapter 2 40
- Circuit Block Diagram 41
- Memory Map 42
- M-T88 Printer Mechanism 43
- Head holding mechanism 44
- Paper feed operation 45
- Thermal head 46
- Paper guide 46
- Frame cover 46
- Main frame 46
- Paper Supply Mechanism 47
- Near end sensor mechanism 48
- Paper end sensor mechanism 48
- Photosensor 49
- Shield plate 49
- Main frame (bottom) 49
- Data input and printing 50
- Cutter Mechanism 51
- Stationary blade mechanism 52
- Movable blade mechanism 52
- Auto cutter operation 53
- Cutter blade knob 53
- Cover Mechanism 54
- Cover open sensor mechanism 55
- Display Mechanism 56
- Display panel 57
- Switch board assembly-B 57
- Push-button 57
- RAM (1M bit) 60
- ROM (2M or 4M bits) 61
- Gate array 61
- Reset circuit 63
- AC_1 AC_2 Operation 64
- HL Clockwise 64
- L H Counterclockwise 64
- H H Brake 64
- Control Panel Control Circuit 65
- DIP Switch Read Circuit 65
- Drawer Kick Control Circuit 65
- Power Supply Circuit 66
- I/F Circuit Board Assembly 67
- Switchboard B 67
- Chapter 3 68
- Printer cover 69
- Control panel 69
- Cutter cover 69
- Cover open button 69
- Loading roll paper 70
- Figure 3-2 72
- Detector screw 73
- Detector lever 73
- Other hole 73
- Problem Solving 74
- CAUTIONS: 75
- Maintenance Procedures 76
- Thermal element 77
- Radiation plate 77
- Print circuit board 77
- Chapter 4 80
- Troubleshooting Flowcharts 81
- POWER does not turn on 82
- PAPER OUT LED does not light 83
- ERROR LED is lit 84
- 4 ERROR LED is flashing 85
- Approx. 160 msec 88
- Using This Manual 92
- Roll paper cover 93
- Cover-thermal-AA 93
- Case-lower-AA block 94
- IC cover 94
- CCS-tite M3x8 94
- Cover-cutter-AA 96
- Case-lower-AA 98
- Mechanism 99
- CPS-tite (O) M3x6 99
- Plate-mechanism 99
- CAUTION: 100
- CAUTION: 102
- Hook part 104
- Switch circuit board 106
- CBS-tite 106
- Cover-frame assembly block 107
- Auto cutter unit block 108
- Paper guide unit block 111
- Cable of pape 112
- Lever-cover open 114
- Tabs on frame assembly 116
- Groove of thermal head 116
- Motor-paper feed-receipt 117
- Frame assembly 118
- Motor (+) Terminal Red 122
- Motor (-) Terminal Black 122
- Microswitch Terminal White 122
- Appendix 127
- Reverse mode 128
- Printer status and signals 129
- RS-485 Serial Interface 131
- Appendix A-8 Rev. A 134
- XON/XOFF Transmit Timing 135
- Data Format When Using RS-485 135
- Printer reception data level 136
- Rev. A Appendix A-11 137
- Appendix A-12 Rev. A 138
- Rev. A Appendix A-13 139
- Appendix A-14 Rev. A 140
- Rev. A Appendix A-15 141
- Appendix A-16 Rev. A 142
- Rev. A Appendix A-17 143
- Case Unit Parts Name List 144
- Rev. A Appendix A-19 145
- Appendix A-20 Rev. A 146
- Overall Exploded Diagram 147
- Rev. A A-22 148
- M-T88 Printer Mechamism 148
- Lubrication Points Diagram 149
- Circuit Board Diagram 150
- RS-232 Interface Board 151
- IEEE 1284 Interface 152
- RS-485 Interface Board 153
- Rev. A A-28 154
Manuais e produtos relacionados com Digitalizar e Imprimir Epson TM-T88II Series
Digitalizar e Imprimir Epson USN 52R Especificações
(207 páginas)
(207 páginas)
Digitalizar e Imprimir Epson 9800 - Stylus Pro Color Inkjet Printer Guia do Utilizador
(385 páginas)
(385 páginas)
Digitalizar e Imprimir Epson LX-300+ Guia do Utilizador
(145 páginas)
(145 páginas)
(42 páginas)
Digitalizar e Imprimir Epson 7900CTP Especificações
(18 páginas)
(18 páginas)
Digitalizar e Imprimir Epson TM-J2000 Especificações
(119 páginas)
(119 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.456 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais