Epson TM-T88II Series Manual de Instruções Página 124
- Página / 154
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
5-34 Disassembly, Assembly, and Adjustment Rev. A
The following is the installation procedure:
1. Install {lever-N.E. detector} on {holder-N.E. detector}.
CAUTION:
The two {lever-N.E. detector} dowels break easily. Take care when performing the
above step.
After installation, check for smooth operation of {lever-N.E. detector}. If operation is not
smooth, remove {lever-N.E. detector} and re-install it.
2. Align the single dowel and install {microswitch D2A-1120} on {holder-N.E. detector}.
3. Secure {microswitch D2A-1120} in place with the single {CBB-tite M2x8} screw.
CAUTION:
Tighten this screw with the specified torque of 0.176 N·m {1.8 Kg·cm}. Overtightening
this screw can deform {microswitch D2A-1120} and result in printer malfunction.
- TM-T88 Series 1
- SEIKO EPSON CORPORATION 4
- Modular type connectors 5
- FCC CLASS A 5
- Introduction 6
- WARNING: 7
- Revision Sheet 8
- Contents 9
- Rev. A vii 11
- Chapter 1 13
- Printing Specifications 14
- Character Specifications 15
- Auto Cutter 15
- Paper Roll Supply Device 16
- Paper Specification 16
- Printable Area 17
- Internal Buffer 18
- Electrical Specifications 18
- Reliability 19
- Environmental Conditions 20
- Connectors 21
- Power Supply Connector 22
- CAUTIONS: 24
- RS-232 serial interface 25
- (continued) 27
- Reset switching 29
- Reset DC characteristics 29
- Buttons and Switches 30
- Panel Button 31
- DIP Switches 31
- Transmission speed 32
- DIP switch 2 32
- Print density selection 32
- For parallel interface model 33
- DIP switch 1 33
- DIP switch 2 33
- Panel LED 34
- Self-test 35
- Hexadecimal Dump 35
- Paper Sensors 36
- Standard Accessories 37
- Consumables 38
- Input specifications 39
- Output specifications 39
- Chapter 2 40
- Circuit Block Diagram 41
- Memory Map 42
- M-T88 Printer Mechanism 43
- Head holding mechanism 44
- Paper feed operation 45
- Thermal head 46
- Paper guide 46
- Frame cover 46
- Main frame 46
- Paper Supply Mechanism 47
- Near end sensor mechanism 48
- Paper end sensor mechanism 48
- Photosensor 49
- Shield plate 49
- Main frame (bottom) 49
- Data input and printing 50
- Cutter Mechanism 51
- Stationary blade mechanism 52
- Movable blade mechanism 52
- Auto cutter operation 53
- Cutter blade knob 53
- Cover Mechanism 54
- Cover open sensor mechanism 55
- Display Mechanism 56
- Display panel 57
- Switch board assembly-B 57
- Push-button 57
- RAM (1M bit) 60
- ROM (2M or 4M bits) 61
- Gate array 61
- Reset circuit 63
- AC_1 AC_2 Operation 64
- HL Clockwise 64
- L H Counterclockwise 64
- H H Brake 64
- Control Panel Control Circuit 65
- DIP Switch Read Circuit 65
- Drawer Kick Control Circuit 65
- Power Supply Circuit 66
- I/F Circuit Board Assembly 67
- Switchboard B 67
- Chapter 3 68
- Printer cover 69
- Control panel 69
- Cutter cover 69
- Cover open button 69
- Loading roll paper 70
- Figure 3-2 72
- Detector screw 73
- Detector lever 73
- Other hole 73
- Problem Solving 74
- CAUTIONS: 75
- Maintenance Procedures 76
- Thermal element 77
- Radiation plate 77
- Print circuit board 77
- Chapter 4 80
- Troubleshooting Flowcharts 81
- POWER does not turn on 82
- PAPER OUT LED does not light 83
- ERROR LED is lit 84
- 4 ERROR LED is flashing 85
- Approx. 160 msec 88
- Using This Manual 92
- Roll paper cover 93
- Cover-thermal-AA 93
- Case-lower-AA block 94
- IC cover 94
- CCS-tite M3x8 94
- Cover-cutter-AA 96
- Case-lower-AA 98
- Mechanism 99
- CPS-tite (O) M3x6 99
- Plate-mechanism 99
- CAUTION: 100
- CAUTION: 102
- Hook part 104
- Switch circuit board 106
- CBS-tite 106
- Cover-frame assembly block 107
- Auto cutter unit block 108
- Paper guide unit block 111
- Cable of pape 112
- Lever-cover open 114
- Tabs on frame assembly 116
- Groove of thermal head 116
- Motor-paper feed-receipt 117
- Frame assembly 118
- Motor (+) Terminal Red 122
- Motor (-) Terminal Black 122
- Microswitch Terminal White 122
- Appendix 127
- Reverse mode 128
- Printer status and signals 129
- RS-485 Serial Interface 131
- Appendix A-8 Rev. A 134
- XON/XOFF Transmit Timing 135
- Data Format When Using RS-485 135
- Printer reception data level 136
- Rev. A Appendix A-11 137
- Appendix A-12 Rev. A 138
- Rev. A Appendix A-13 139
- Appendix A-14 Rev. A 140
- Rev. A Appendix A-15 141
- Appendix A-16 Rev. A 142
- Rev. A Appendix A-17 143
- Case Unit Parts Name List 144
- Rev. A Appendix A-19 145
- Appendix A-20 Rev. A 146
- Overall Exploded Diagram 147
- Rev. A A-22 148
- M-T88 Printer Mechamism 148
- Lubrication Points Diagram 149
- Circuit Board Diagram 150
- RS-232 Interface Board 151
- IEEE 1284 Interface 152
- RS-485 Interface Board 153
- Rev. A A-28 154
Manuais e produtos relacionados com Digitalizar e Imprimir Epson TM-T88II Series
Digitalizar e Imprimir Epson USN 52R Especificações
(207 páginas)
(207 páginas)
Digitalizar e Imprimir Epson 9800 - Stylus Pro Color Inkjet Printer Guia do Utilizador
(385 páginas)
(385 páginas)
Digitalizar e Imprimir Epson LX-300+ Guia do Utilizador
(145 páginas)
(145 páginas)
(42 páginas)
Digitalizar e Imprimir Epson 7900CTP Especificações
(18 páginas)
(18 páginas)
Digitalizar e Imprimir Epson TM-J2000 Especificações
(119 páginas)
(119 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.146 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais