Epson PA-295 Instruções de Operação Página 1

PA-295Installation & Operating Instructions 99795 09/18/01

Be sure to use a ribbon cassette that meets theprinter's specifications. The EPSON ERC-27 isrecommended.• Note:For instructions on replacing a us

Be sure to perform the steps above because it is necessary tomake sure that the printer is in the paper release mode beforeyou install the ribbon cass

6.Carefully insert the ribbon cassette in the printer as shown inthe illustration below. Notice exactly where the ribbon must go.7.Then push firmly on

Insert the paper from either the front or the side, as shown inthe illustration below. Insert the paper into the printer until it isstopped by the for

3.While holding down the RELEASE button, turn the printerback on.4.Remove your finger from the RELEASE button. Theprinter prints the current printer s

Turn the printer over and locate the DIP switches, asshown below.2.7Notice that ON is marked on the set of switches. Usetweezers or another narrow too

PA-295Transmission Speeds1-16 InstallationPrints'?'FunctionIgnoredSwitchData reception error35 bytes512 bytesReceive buffer capacityXON/XOFF

The control panel has three buttons and threelights.ButtonsAll three of these buttons can be disabled or enabled by the ES Cc 5 command.RELEASEPressin

RELEASEThis light is on when the printer is in the paper release mode andit is off when the printer is in the clamp mode. Paper can beinserted only wh

Then remove the used ribbon by grasping the handle and pullingstraight out, as shown by the arrow in the illustration below.Then follow the rest of th

PA-295P(1) Upper case(2) Printer cover(3) Operation panel(4) Document table(5) POWER switch(6) Interface connector(7) FG(8) Drawer kick-out connector(

This chapter gives the solutions to some printerproblems.The POWER light does not comeon.Make sure that the power supply cables are correctly pluggedi

Printing Method:Impact dot matrixHead Wires7-pin shuttle typeUnidirectionalPrinting Direction:Lines per second5 x 7 font: 1.9 to 2.37 x 7 font: 1.9 to

Character size:5 x 7 font:ANK: 1.6 mm (.063") x 2.9 mm (.114")Graphics: 1.9 mm (.075") x 2.9 mm(.114")7 x 7 font:ANK: 1.3 mm (.051

Single Ply Paper: 0.09 to 25mm Copy capability andpaper thickness:No copies(single-ply)-.0.09 to 0.25 mm1.0035" to.0098.ff) (135 kgpaper orequiva

Copying capability is influenced bythe ambient temperature. Printingmust be performed under theconditions, described in a Tablebelow:Relationship betw

Printing positionNotesThe mechanical form stopper is adjustable in the range 26.5to 36.5 mm (1.04" to 1.44")1.The TOF and BOF sensors are fi

Supply voltage:+24 VDC ± 10%Current consumption:Operating(except fordrawer kick-out):Mean - approx.600 mA at 24VDC (full-columnprinting and datatransm

Life:Mechanism: 3,000,000 linesPrint head: 100 million characters(when in the averageof 2 dots/wire percharacter.)Reliability• End of Life is defined

Environmental ConditionsTemperature:Operating:5º to 40ºC (41º to104ºF)Storage: -I0º to 50ºC (14ºto 122ºF) (exceptfor ribbon andpaper)Humidity:Operatin

The illustration below shows the items included for the standardspecification printer.If any item is damaged, please contact your dealer forassistance

The printer is protected during shipping by a transportationdamper that must be removed before you turn on the printer.1.Pull the damper out and remov

PA-295You need an appropriate serial interface cable to connectyour computer to the printer.1.Make sure that the printer and the computer are turned o

2.Connect the other end of the cable to the connector onyour computer.PA-295You need an appropriate parallel interface cable to connectyour computer t

Plug the drawer cable into the drawer kick-out connector on theback of the printer next to the computer interface connector.PA-295PA-295PDo not connec

You need an appropriate ground wire to ground your printer.Recommended wire is described below.AWG 18 or equivalent3.2Thickness of wire:Diameter of te

This printer requires an external power supply. The EPSONPower Supply PS-150 is recommended.Using an incorrect power supply can cause serious damage t